SPE Library


The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.

The SPE Library is just one of the great benefits of being an SPE member! Are you taking advantage of all of your SPE Benefits?

Not an SPE member? Join today!

Use % to separate multiple keywords. 


Search SPE Library
    
    




Sort By:  Date Added   Publication Date   Title   Author

Conference Proceedings

Three-Dimensional Computer-Aided Mold Cooling Design for Injection Molding
Rong-Yeu Chang, Wen-Hsien Yang, David C.Hsu, Venny Yang, May 2004

Mold cooling system design in injection molding is of great importance because it is crucial not only to reduce molding cycle time but also to improve part quality. Traditional mold cooling analysis is based on the hybrid finite-difference/ boundary element (FD/BEM) approach. This approach was developed to accommodate the conventional 2.5D Hele-Shaw flow-based shell element model. In this paper, a true three-dimensional mold cooling analysis approach is developed. A fully tree-dimensional numerical analysis faithfully simulates the effects of part geometry, cooling system design, and ambient temperature on the solidification of the part. Finite volume method (FVM) is adopted as the numerical engine of the new approach. This developed approach is proved from numerical experiments to be a cost-effective method for true 3D simulation in injection mold cooling analysis.

Optimization of the Warpage of Fiber Reinforced Thermoplastics by Influencing the Fiber Orientation
R. Haag, May 2004

This paper describes a new commercial simulation tool to simulate the injection molding process and the warpage of fiber reinforced thermoplastics considering the anisotropic behavior. A full 3D formulation of the Navier-Stokes equations with a VOF algorithm for the description of the free surface motion is used to simulate the filling process. The transport of the fiber orientation is calculated by the Folgar-Tucker equation using a hybrid closure approximation. The resulting fiber orientation tensor is used for the calculation of the anisotropic mechanical behavior. The Halpin-Tsai equations provide the anisotropic material data for the calculation. Through an real-life example it will be shown that the knowledge of the fiber orientation can be used to optimize the runner system in order to change the local fiber orientation and thereby to optimize the warpage of the part.

Effect of Colorant Carriers on Strength of Weld Lines in Polypropylene
G. Samuel Brockway, Thomas R. Ellis, May 2004

In this study, the effects of polyethylene (PE) and polypropylene (PP) colorant carriers for various levels of loading on the short-term strength of weld lines in homopolymer polypropylene are quantified. Tensile bars (“dog bones”) were molded with an intentional weld line in the gauge length of the bars for a variety of material mixes. When tested at room temperature, the colorants with the polyethylene carrier drastically reduced the tensile elongation of the bars when compared with an unpigmented sample. The reduction was so severe that the PE-carrier specimens broke before yielding, thus exhibiting significant loss of strength. Samples of PP having the colorant with the PP carrier, while breaking at significantly lower elongation than their unpigmented counterparts, showed no reduction in weld-line strength because they yielded. Elevated temperature results are less dramatic, the unpigmented and PP-colorant samples yielded and stretched beyond 450%, while three-fifths of the PE-colorant specimens exhibited a yield. A PP co-polymer with PP-based colorant was also studied. In addition, slow strain-rate data is presented for a few compounds, and the rate / temperature dependence is discussed. Finally, several samples were aged at elevated temperature and subsequently tensile tested at room temperature. The results showed reductions in elongation but not weld-line strength.

The Influence of Mould Temperature and Polymer Structure on the Mechanical and Thermal Properties of Metallocene Catalysed LLDPEs
S. Walker, G. Mc Nally, P.J. Martin, May 2004

A number of metallocene and conventional LLDPEs, with different material properties, were injection moulded over four different mould temperatures. An assessment of the effect of cooling rate and polymer properties on the mechanical performance of the specimens was conducted to establish any significant correlations. Rheological studies of the materials under high shear rates experienced in injection moulding, was performed to determine flow characteristics of the materials. Differential scanning calorimetry (DSC) and dynamic mechanical thermal Analysis (DMTA) were used to study the influence of the comonomer type and degree of branching on the properties of the materials.

The Effect of Nitrogen Purging on Degradation during Reprocessing in Injection Molding
J.S. Archer, S.H. Dillman, May 2004

This study investigated the effect of nitrogen purging in the material hopper on the melt flow index (MFI), residual oxidative induction time (OIT), color and impact strength of impact modified polypropylene copolymer and polycarbonate during repeated reprocessing through an injection molder. Heat history had the expected effect of increasing MFI, changing color and decreasing impact strength for both resins and decreasing OIT in polypropylene. In polypropylene nitrogen purging significantly reduced the changes in MFI and OIT resulting from repeated reprocessing. However, nitrogen purging did not have a significant effect on the properties of polycarbonate, probably due to its inherent resistance to oxidative degradation.

The Effect of Phthalocyanine Pigment on the Microstructural and Mechanical Performance of Propylene-Ethylene Block Copolymer
I.F.M Major, G.M. McNally, May 2004

Injection moulded samples of a commercial propylene-ethylene block copolymer containing 0% - 8% phthalocyanine blue pigment were prepared using a range of mould temperatures (40°C - 80°C). Mechanical and thermal analysis showed progressive increase in tensile modulus, storage modulus (E’) and glass transition temperature (Tg) with increase in pigment loading. However, impact strength of the pigmented copolymer decreased progressively with increase in pigment loading and mould temperature. Thermal analysis of the samples shows that changes in crystalline melting phase ?H, and activation energies Ea for phase relaxations (DMTA) may account for the overall decrease in impact performance of the pigmented copolymer.

Microcellular Nanocomposite Injection Molding Process
Mingjun Yuan, Lih-Sheng Turng, Rick Spindler, Daniel Caulfield, Chris Hunt, May 2004

This study aims to explore the processing benefits and property improvements of combining nanocomposites with microcellular injection molding. The molded parts produced based on the Design of Experiments (DOE) matrices were subjected to tensile testing, impact testing, and Scanning Electron Microscope (SEM), Transmission Electron Microscope (TEM), Dynamic Mechanical Analysis (DMA), and X-ray Diffraction (XRD) analysis. Effects of processing conditions on the mechanical properties and microstructures have been studied. The results show that the supercritical fluid (N2) helps to further exfoliate and uniformly disperse the nano-clays in the matrix during the course of molding process. Compared to the corresponding base polyamide microcellular parts, the microcellular nanocomposites exhibit better cell structures and cell distributions as well as better mechanical properties.

Applications of Polyamide/Cellulose Fiber/Wollastonite Composites for Microcellular Injection Molding
Herman Winata, Lih-Sheng Turng, Daniel F. Caulfield, Tom Kuster, Rick Spindler, Rod Jacobson, May 2004

In this study, a cellulose-fiber-reinforced Polyamide-6 (PA-6) composite, a hybrid composite (PA- 6/cellulose/Wollastonite), and the neat PA-6 resin were injection molded into ASTM test–bar samples with conventional and microcellular injection molding. The impact and tensile strengths of molded samples were measured and the Scanning Electron Microscopy (SEM) images were taken at the fracture surfaces. The effects of filler systems and the introduction of microcellular structure on the impact and tensile strengths were studied. It was found that the cellulose fibers and the cellulose/Wollastonite fillers improve the tensile strength and tensile modulus. In addition, the microcellular injection molded neat resin exhibits a higher impact strength than that of the conventionally molded solid part. However, a reduction in tensile strength was observed with both of the filled composites when molded with microcellular injection molding. This could be attributed to microcells at the interface of cellulose fibers and the polymer matrix.

Fracture Toughness Evaluation of Adjacent Flow Weldline by SENB Method
Kohji Yamada, Kiyotaka Tomari, Toshihiko Harada, Hiroyuki Hamada, May 2004

Fracture toughness of adjacent flow weldline occurring around an obstructive pin was evaluated by single edge notched bend (SENB) method. The fracture toughness near the pin was higher than any other part of the weldline. The fracture toughness decreased drastically along the weldline and then increased gradually toward the end of the specimen. These characteristic features could be explained by flow-induced molecular orientation at the weldline interface. The material flow beside the pin stopped in the middle of the filling process. Molecular orientation parallel to the weldline due to the fountain flow relaxed since no shear stress affected the area, resulting in high molecular entanglement across the weldline. On the contrary, at the downstream side the material kept on flowing during the filling process. This indicated that the molecular orientation could not relax due to flow-induced stress during the process. The magnitude of these two areas was dependent on the position of first collision point (FCP) at which two melt fronts collided first behind the pin. The V-notch depth on the surface of the specimens was also dependent on the distance from FCP.

Flow-Induced Crystallization and Birefringence in Injection Molding of Semicrystalline Polymers
Kyuk Hyun Kim, A.I. Isayev, Keehae Kwon, May 2004

A novel approach for the numerical simulation of frozen-in birefringence in moldings of semicrystalline polymers was proposed. The approach was based on the calculation of elastic recovery and crystalline orientation function frozen when the stress-induced crystallization occurred. The flow effect on the equilibrium melting temperature elevation due to the entropy reduction between the oriented and unoriented melts was incorporated to model crystallization. To find frozen-in elastic recovery and entropy change, a non-linear viscoelastic constitutive equation was used. The crystalline and amorphous contributions to the overall birefringence were obtained from the crystalline orientation function and the flow birefringence, respectively. The skin layer thickness and birefringence profiles were predicted and measured in moldings of polypropylenes of different molecular weights at various processing conditions.

Adiabatic Splay and Blush in Injection Molded Parts
Paul Van Huffel, May 2004

Most molders are aware of the potential for creating burn marks where air gets trapped in molded parts. What no one seems to consider is blush or splay marks that manifest specifically along knit lines and would otherwise be assumed to be the effect of shear. The only problem is that the shear cannot be accounted for in the tool design. The cause can be traced back to trapped air, predicted with mold filling analysis software (as such), and verified with physical testing. The purpose of this paper is to give proper definition to this defect and distinguish it from burns and short-shots as caused by air entrapment, and thus can be more easily identified and remedied.

Fibre Orientation in Weldline Areas - Investigation of an Air Intake Manifold
Stefan Roth, Ines Kuehnert, Guenter Mennig, May 2004

The focus of attention is kept on weldline behavior in parts of complex geometry, i.e. the upper part of an air intake manifold. By simulating the filling process using simulation software, the fiber orientation and the filling was calculated and compared to experimental studies. Thereby, a rather inhomogeneous filling behavior was found, caused by an unequally balanced runner system that leads to changes of the flow direction within the cavity during the injection process. These circumstances prevent the weldlines zones from spreading throughout the part. Hence, a distinct control of an uneven flow front pattern could help to reduce the weldline area and therefore minimize zones of optical and mechanical weak points in plastic parts.

Effects of Design Solutions and Moulding Operating Conditions in Warpage
P.G. Martinho, C.C. Neves, A.M. Brito, May 2004

Injection molded parts with plane surfaces and complex flow are subjected to distortion depending on the mould geometry and general processing conditions. In this study, the effects of several mould and part design solutions were evaluated as well as the operating conditions of the injection molding machine. To examine warpage, the geometry of the plastic parts was defined and a modular mould was designed integrating pressure and temperature sensors. Experimental results, namely pressure, temperature and warpage values, were compared with those obtained from C-MOLD simulations.

3D CAE Simulation and Verification for the Ferrule of MT-RJ Fiber Connector
Wen-Ren Jong, Shia-Chung Chen, Shin-Hao Hung, Ming-Hsiu Chung, Tsung-Hsiang Kuo, Shrwai Ho, May 2004

Because communication and Internet are so popular, light communication will become an efficient way to send message in the next generation. Optical fiber connector becomes an important component that connects, divorces or reunites the fiber, light source, light sensor and the other fiber ferrule connector. Because of the tiny size of products and the demand of precision, the decrease of manufacturing cost and the increase of demanded precision will be a huge obstacle that has to be overcome.This paper presents the study for the molding of ferrule in MT-RJ fiber connectors. The work includes the design of molding configuration with three different gating locations which are used to study the effects for the critical dimensions and precision of fiber holes. In addition, the 3D CAE software are used to simulate and verify the molding results. Moreover, the Taguchi method is used to find optimal processing conditions for resolving the void problems.

Practical Experiences with a System for In-Line Monitoring of Melting Spherulites in Semicrystalline Polypropylene Sheets
Edmund Haberstroh, Jürgen Wirtz, May 2004

In thermoforming, it is found difficult to process Polypropylene if the heating control is based on measured sheet temperatures. It is shown that monitoring the melting of spherulites provides a better method. Testing is carried out using a novel device transmitting a laser beam through the PP-sheet. The scattering of the beam at spherulites within the sheet is indirectly measured via remaining beam intensity behind the sheet. With translucent Polypropylene, the melting of spherulites can be observed during heating.

Twin Sheet Thermoforming of a Fuel Tank with a Converted Blow Mould
C. deGrandpré, N. Nardini, P. Girard, L. Savoni, R. DiRaddo, May 2004

Twin sheet thermoforming has increased in usage over the last ten years, in particular due to its inherent ability to produce hollow parts and consequently challenge blow moulding. Blow moulded automotive fuel tanks are the parts that are the most challenged by twin sheet thermoforming.This work considers the conversion of a fuel tank blow mould for use in twin sheet thermoforming. The added challenge for the project is that the mould needs to maintain a flexibility to return to blow moulding, upon demand. Furthermore, the work includes the use of finite element simulation to reduce the sheet heating times.

On-Line Hybrid Model Based Tuning of Simulation Provides Soft Sensors for the Estimation of Sheet Temperature Distributions in Thermoforming
P. Girard, V. Thomson, B. Hou, A. Yousefi, R. DiRaddo, May 2004

Some of the main problems to be solved when applying simulation to a process are the discrepancies between the predicted and measured parameters. This can be due to the fact that the actual operating conditions are different from the ones that were input into the simulation due to variations in material properties and errors in the assumptions for the simulation model. This work proposes a technique to tune the results of the simulation to the actual sensor outputs of the machine. The simulation can then be used as a generalized soft sensor for the process: Since the model of the simulation has been fitted to the actual process, the predictions of the simulation for non-readily accessible points will be that much closer to reality. A further advantage is that variations of the process are back-propagated to the input, so that faults that may appear in the system are presented as more easily interpretable variations of the input data.

The Science Based Optimization of Material Heating during Thermoforming Processes
Bunyong Rungroungdouyboon, John P. Coulter, May 2004

In this paper, the optimized radiative heating of opaque thermoplastic sheet during thermoforming processes has been studied by using a newly developed modeling and optimization approach. The net radiation method has been employed to develop a comprehensive numerical code that can compute the total radiative heat and associated temperature developments locally on the thermoplastic sheet. The resultant simulation model can accommodate full non-symmetric zone heating situations and multi-layered forming materials. A coupled optimization package was then developed to obtain optimized heater pattern solutions that will lead to desired material temperatures during thermoforming processes. This is done by specifying a desired thermoplastic sheet temperature distribution and iteratively solving for the heater setting needed to obtain the desired results

Modeling of the Behavior of Semi-Crystalline Polypropylene at Elevated Strain Rate and Temperature
K.Y. Tshai, E.M.A. Harkin-Jones, P.J. Martin, G.H. Menary, May 2004

A non-linear viscoelastic model comprised of two components, a rubber-like hyperelastic component and a viscoelastic time-dependent relaxation spectrum was used to model the behavior of semi-crystalline PP at rates and temperatures close to that found in the thermoforming process. Temperature dependence was introduced through time-temperature-superposition (TTS) using WLF. The hyperelastic constants were identified from equibiaxial tensile experimental tests while the time-dependent relaxation spectrum was characterized through a temperature-frequency sweep analysis from a strain controlled DMTA test. Results show that the developed model is capable of simulating the behavior of semicrystalline PP fairly well.

Polymer-Polymeric Friction at Temperatures and Rates Simulating the Thermoforming Process
Bernhard Hegemann, Peter Eyerer, Noel Tessier, Karel Kouba, Tom Bush, May 2004

Plug assist thermoforming is one of the most important process variants for the thermoforming industry. The purpose of the plug assist is to pre-stretch the heated polymer sheet prior to the application of pressure and/or vacuum during the final part formation. Parametric studies performed on simulation models of the thermoforming process have shown friction between the polymer and the plug assist to be critical in predicting material distribution in the thermoformed part.This report presents the results of investigating the friction behaviour of a polymer to plug assist material at thermoforming conditions. A new measurement technique to determine friction coefficients will be shown and explained in detail. This technique allows the characterization of the friction coefficient as a function of temperature and rate and shows the sensitivity respectively.







SPE-Inspiring Plastics Professionals

© 2024 SPE-Inspiring Plastics Professionals.
All rights reserved.

84 countries and 60k+ stakeholders strong, SPE unites plastics professionals worldwide – helping them succeed and strengthening their skills through networking, events, training, and knowledge sharing.

No matter where you work in the plastics industry value chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor what your background is, education, gender, culture or age-we are here to serve you.

Our members needs are our passion. We work hard so that we can ensure that everyone has the tools necessary to meet her or his personal & professional goals.

Contact Us | Sitemap | Data Privacy & Terms of Use

Links

Locations

SPE US Office
83 Wooster Heights Road, Suite 125
Danbury, CT 06810
P +1 203.740.5400

SPE Australia/New Zealand
More Information

SPE Europe
Serskampsteenweg 135A
9230 Wetteren, Belgium
P +32 498 85 07 32

SPE India
More Information

SPE Middle East
More Information

3Dnatives Europe
157 Boulevard Macdonald
75017, Paris, France
More Information

Powered By SPE

SPE-Inspiring Plastics Professionals

SPE-Inspiring Plastics Professionals

SPE ImplementAM

SPE-Inspiring Plastics Professionals

SPE-Inspiring Plastics Professionals

SPE-Inspiring Plastics Professionals




spe2018logov4.png
  Welcome Page

How to reference articles from the SPE Library:

Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:

Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers
Available: www.4spe.org.

Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.

If you need help with citations, visit www.citationmachine.net