SPE Library


The SPE Library contains thousands of papers, presentations, journal briefs and recorded webinars from the best minds in the Plastics Industry. Spanning almost two decades, this collection of published research and development work in polymer science and plastics technology is a wealth of knowledge and information for anyone involved in plastics.

The SPE Library is just one of the great benefits of being an SPE member! Are you taking advantage of all of your SPE Benefits?

Not an SPE member? Join today!

Use % to separate multiple keywords. 


Search SPE Library
    
    




Sort By:  Date Added   Publication Date   Title   Author

Conference Proceedings

The Properties of Injection Molded, Short and Long Carbon Fiber Reinforced Polyamide 6,6 Composites
A.B. Hassan, A.H. Yahaya, P.R. Hornsby, M.J. Folkes, May 2001

Injection molding the dry blend of fibers and matrix granules usually results in composite materials with poor surface finishes, high mould shrinkage and variable strength. Therefore, the process usually involved two stages, i.e. compounding and molding. This process however, is associated with the problem of fiber breakage. In this work, short and long carbon fiber reinforced polyamide 6,6 composites, prepared by extrusion and pultrusion compounding respectively, were injection molded. Test pieces were then subjected to the fiber length distribution characterization and mechanical test. It was found that pultrusion compounded composites showed superior fiber characteristics compared to the extrusion compounded composites counterpart. Number average fiber length (Ln) and weight average fiber length (Lw) supports this behavior. These fiber length characteristics were also in agreement with the improved tensile strength and tensile modulus of long fiber composites over the short fiber composites, despite the reduction in their fracture strain.

The Effect of Injection Moulding Processing Conditions and ?-Olefin Co-Monomer Type on the Performance of Metallocene Catalysed Polyethylenes
S. Walker, G.M. Mc Nally, P.J. Martin, M. Murphy, May 2001

A number of metallocene catalysed linear low density polyethylenes and a conventional LDPE, of different material properties, were injection moulded over different mould cooling conditions. An assessment of the effect of the cooling rate, density and the co-monomer type on the mechanical performance and crystallinity was then conducted in order to establish any underlying trends. The results obtained from this report show a direct correlation between the density and co-monomer type of the materials with the mechanical properties, and a less significant relationship with the mould temperatures.

Bulk Moduli from Enthalpy and Volume Data Obtained during Physical Aging Experiments
P. Slobodian, V. Pelíšek, J. Kubát, P. Sáha, May 2001

Sudden temperature change stimulated process of physical aging has been studied through enthalpy and volume relaxation. The investigated polymers were a-PMMA and its amorphous blends containing 6 and 14vol.% of PEO. Differential scanning calorimetry and mercury-in-glass dilatometry were employed. Based on [1], where Kubát at al. suggested the possibility of correlation of enthalpy and volume relaxation data, apparent bulk moduli, Ka, were calculated and compared with the moduli determined by direct compression. The correlation between computed and measured data was reasonably good.

The Use of Maleic Anhydride-Containing Concentrates to Effect Adhesion between Polyethylene and Ethylene-Vinyl Alcohol
Gregory W. Kamykowski, May 2001

Adhesion properties were determined on five-layer coextruded cast films that consisted of two high density polyethylene (HDPE) cap layers, two tie layers, and an ethylene-vinyl alcohol copolymer (EVOH) barrier layer (ABCBA configuration). The tie layers consisted of varying amounts of maleic anhydride-modified polyethylene-containing concentrates and various diluting resins. The extrusion temperature was also varied. Adhesion increased fairly uniformly as the film thickness and the concentrate level were increased. Adhesion was also affected by the choice of diluent and the ethylene content of the EVOH. Adhesion did not vary over our experimental temperature range.

Morphology Distribution of Injection Molded Polypropylene and its Dependence on Processing History
G. Liu, G. Edward, May 2001

In this paper, the morphology distribution of injection molded ZMA 6170 polypropylene observed using polarized optical microscopy is reported. A three-region- multi-layer model is sufficient to describe the skin-core morphology of these injection-molded parts. In the fully developed flow regions, a clear three-layer structure composed of a surface skin layer, a transition layer, and an inner core layer is observed. The simulation software package Moldflow MPI is used to identify the thermal and shear histories of the polymer melt during injection molding process. The characterization of each layer and its dependence on the thermal and shear histories are discussed.

The Developing Behavior of Core Material and Breakthrough Phenomenon in Sandwich Injection Molding
Daisuke Watanabe, Hiroyuki Hamada, Kiyotaka Tomari, May 2001

The sandwich injection molding technique can be used in wide range of engineering applications. In this study, the developing behavior of core materials and break through phenomenon in the sandwich injection molding was investigated. The samples were preferred using a spiral-flow mold by changing the viscosity ratio and the melt temperature of skin and core materials. Developing behavior of the materials in sandwich injection moldings divided four regions, and it is noted that core material tends not to completely penetrate through the skin material at a stretch point, and it resulted in break through phenomenon. It is considered that break through phenomenon depends on the melt strength of the freezing layer of the skin material at flow front.

Mechanical Properties of Knitted PE Fiber Reinforced PE Injection Molding Composites
Tatsuro Fukui, Hiroshi Ishida, Asami Nakai, Hiroyuki Hamada, Kazuaki Nishiyabu, May 2001

Interface construction is very important in the design of composite materials. Composites that consist of same materials but different shape such as fiber shape and matrix phase can create high interfacial strength. Call this composite Interface-less Composites". In this study knitted fabric was chosen as reinforcement configuration which has good drapability expandability and high productivity. Knitted polyethylene (PE) fiber reinforced PE film (PE/PE composite film) by film stacking method was prepared. Injection molding specimens were prepared by inserting this PE/PE composite film and PE was injected as matrix. Tensile properties of Interface-less composites by using injection-molding method were investigated."

Study of Damage Mechanisms in Uni-Weave/Satin-Weave Hybrid IM7/BMI Composites under Uniaxial Tensile Loading
Chao Li, Xiaodong Tang, Hung-Jue Sue, John D. Whitcomb, May 2001

The damage mechanisms in uni-weave/satin-weave hybrid IM7/BMI composites under uniaxial static tension loading have been investigated. The results reveal that hybridization effects on the damage mechanisms largely depend on the degree of waviness. For low waviness composites, the damage process is not affected significantly by hybridization. The damage patterns in the woven and hybrid composites are similar to those found in tape laminate. However, the large waviness composites exhibit complex damage behavior. Hybridization has a significant effect on the damage process.

Mechanical Properties of PP/PP Composites
Takeo Kitayama, Kentaro Ishikura, Hiroyuki Hamada, Takeshi Kikutani, Hiroshi Ito, May 2001

The interfacial structure and mechanical properties of polypropylene (PP/PP) composites consisting of homo-PP fiber and propylene-ethylene random copolymer matrix were investigated. In PP/PP composites, the transcrystalline structure grows on PP fiber, which influences the mechanical properties. The two types of unidirectional PP/PP composite with different impregnating system were fabricated. In the well impregnated PP/PP composites, there were many transcrystalline layers, and the tensile modulus and strength were higher than those of badly impregnated PP/PP composite. Particularly in the transverse direction, well impregnated PP/PP composites had good adhesive properties. Therefore, it is supposed that the mechanical properties of PP/PP composites are influenced by trenscrystalline.

Application of Micro-Braiding Technique to Long-Fiber Reinforced Thermoplastic Composite
A. Nakai, M. Kamaya, E. Fukui, Y. Uetsuji, H. Hamada, May 2001

'Micro-braided yarn' has been proposed as a means of overcoming the difficulty of manufacturing long fiber reinforced thermoplastic composites. Micro-braided yarn is intermediate material for long-fiber reinforced thermoplastic composite. In the Micro-braided yarn a reinforcement fiber is covered by a matrix fiber. In this study, unidirectional carbon-fiber/ PA6-Nylon composites manufactured from micro-braided yarn with different strand diameter were molded in order to investigate the effect of the molding conditions on impregnation mechanism. Through this the mechanical properties of micro-braided composites were understood. A microscopic observation was performed with optical microscopy to understand the impregnation mechanism of thermoplastic resin into the fiber bundle. A parameter for the impregnation property was proposed based on the impregnation volume. 3-point bending test was carried out to investigate the effects of diameter of reinforcements strand in micro-braided yarn and molding condition on the mechanical properties.

Textile Composites with Affordable Interphase
Hiroyuki Hamada, Yoshimichi Fujii, Mitsukazu Ochi, Kazuo Kitagawa, Kazuaki Nishiyabu, Tsuyoshi Nishiwaki, Yasutomo Uetsuji, Masaya Kotaki, Machiko Mizoguchi, Asami Nakai, Naoyuki Oya, Toshiko Osada, Masahiro Yamanouchi, Nobuyoshi Kajioka, May 2001

The fiber/resin interface can be considered to have three-dimensional region, so that technical term of interphase has been often used instead of interface. Interphase should be considered as the third component in fiber reinforced composite materials, and is generated during composite manufacturing. The authors have tried to apply a new function to interphase and called Affordable Interphase". As an example of affordable interphase we have developed the composites with more flexible interphase than matrix resin. In this study we applied the concept of flexible interphase to the woven fabric composites. As a result it was cleared that tensile strength was improved because flexible interphase restrained generation of cracks at interphase inside of fiber bundles."

Development of High Quality Recycled Polyethylene Resins for the Replacement of Virgin Resins
Violet Stefanovski, Edward Kosior, Syed Masood, Pio Iovenitti, Igor Sbarski, May 2001

Dairy and fruit juice bottles are a major source of post consumer recycled high density polyethylene (PCR HDPE). The recycled HDPE has limited post-consumer applications due to its poor stress crack resistance (SCR). This paper presents a review of a test method for SCR and some preliminary results of the development of recycled HDPE blends with improved SCR. The improvement has been achieved with the addition of a modifier, and results indicate that there is a potential to incorporate the use of recycled HDPE in non-pressure pipe applications. These customised blends have been tested for SCR according to the Notched Constant Ligament Stress (NCLS) test. The NCLS test is a new test method (ASTM F17.40) which is currently under development. The NCLS test will be used to determine the susceptibility of HDPE resins to slow crack growth (SCG) under a constant ligament stress in an accelerated environment. The results from the test will subsequently be correlated with field performance results.

The Development of Geometry and Polymer-Independent Product Quality Models Based on Injection Molding Cavity Pressure
David C. Angstadt, John P. Coulter, May 2001

Previous product quality models based on cavity pressure suffer from being geometry and polymer specific and requiring large amounts of data to develop. The present study focuses on the development of geometry/polymer independent models to predict part weight with a minimum of experimental data. Several product geometries were created using inserts in a standard ASTM tensile specimen cavity. Both amorphous and semi-crystalline polymers were utilized. Real-time cavity pressure data was collected, quantified via pressure curve attributes" and used to develop predictive models through multivariate linear regression. Future work will apply the model results to the molding of a typical commercial electrical connector."

Development of Rapid Heating and Cooling Mold Inserts Comprising a Heating Layer, an Insulation Layer and a Substrate
Donggang Yao, Ming Chen, Byung Kim, May 2001

The injection molding process has several inherent problems associated with the constant temperature mold. A basic solution is the rapid thermal response molding process that facilitates rapid temperature change of the mold surface thereby improving quality of molded parts without compromising cycle time. Rapid heating and cooling systems consisting of one metallic heating layer and one oxide insulation layer were investigated in this paper. Design issues towards developing a mold capable of raising surface temperature from 25°C to 250°C in 2 seconds and cooling to 50°C within 10 seconds were discussed. To reduce thermal stresses in the layers during heating and cooling, materials with closely matched low thermal expansion coefficient were used for both layers. Effects of various design parameters, such as layer thickness and material properties, on the performance of the mold were studied in detail with the aid of heat transfer simulation and thermal stress simulation. Several rapid thermal response mold inserts were constructed on the basis of the simulation results. The experimental heating and cooling response agrees with the simulation and also satisfies the target heating and cooling requirement.

Using Truncated Relaxation Spectra in the Simulation of Viscoelastic Flows
Marie-Claude Heuzey, Paula Wood-Adams, André Fortin, May 2001

The simulation of polymer viscoelastic flows is a complicated problem and until now it is not possible to perform simulations that are relevant from an industrial perspective. One of the limiting factors is the degree to which elasticity plays an important role in the flow. For a given constitutive equation and numerical technique, a higher material relaxation time, will result in a lower maximum deformation rate for which convergence is possible. Since industrial processes typically involve very large deformation rates, a practical way to allow their simulation might be to truncate the longest relaxation times. In this work the Leonov constitutive equation was used to simulate flow through an abrupt contraction. The possibility of truncating the relaxation spectrum was explored and the impact of using truncated spectra on simulations is described. Finally we propose a technique for obtaining a truncated relaxation spectrum that will be useful for flow simulations.

Effect of Compatibilization and Dynamic Vulcanization on the Microstructure and Performance of Polyethylene Terephthalate/Elastomer Blends
Pei Lian Ma, Basil D. Favis, Michel F. Champagne, Michel A. Huneault, Florin Tofan, May 2001

Blends of polyethylene terephthalate (PET) and ethylene-ethyl acrylate-maleic anhydride terpolymer (E-EA- MAH) were dynamically crosslinked in a one-step extrusion process. An amine-terminated glycol reacting with MAH moieties was used as the crosslinking agent. Systems were compatibilized by addition of ethylene-methyl acrylate-glycidyl methacrylate terpolymer (E-MA-GMA). The tensile properties and dynamic mechanical thermal analysis response of the unvulcanized and the dynamically vulcanized systems were studied. The effect of blend composition, compatibilization, dynamic crosslinking and processing conditions on the microstructure and tensile properties were investigated.

Deformation and Orientation of Polyamide 6 Nanocomposite
D.C. Worley II, M.K. Akkapeddi, E.P. Socci, May 2001

Mechanical deformation induced experimentally using a T. M. Long stretcher enabled an investigation of the effect nano size platelets can have on the clarity, barrier and mechanical properties of a polymerized nano polyamide 6. Clarity of cast film specimens did show a direct correlation between %Haze and nano platelet concentration. Non nano containing films biaxially stretched 2 times its original dimensions had a 1% - 3% haze reading. Nano containing films ranged from 5% -~ 20% over a nano concentration of 1.0% - 4%, respectively. The oxygen transmission rate, OTR , of 2% and 4% nano films had a 3X and 6X improvement in OTR compared to the unfilled polyamide 6 film, respectively. Biaxed nano polyamide 6 film did not significantly improve OTR, as is the case with non-nano containing polyamide 6 films. There was only a 6% improvement in OTR, which was due primarily to the minimal increase in molecular orientation or packing, which is shown by the small change in the degree of orientation ~77% to 83% for as cast nano films compared to biaxed nano containing films, respectively. The nano containing films do have improved modulus and yield strength and an expected reduction in elongation at break. By taking advantage of molecular orientation mechanical properties were modified via biaxially orientation.

Analysis of Feed Characteristics on the Performance of Groove-Feed Extruders
Michael R. Thompson, John P. Christiano, May 2001

The effect of varying the feedstock shape on the output performance of groove-feed extruders was examined. Pellets of five different aspect ratios were run, as were five different levels of bottle regrind blended with virgin pellet. The different feedstock materials were compared on two different screw designs with differing feed zone geometries. The results showed that different aspect ratios or bulk densities had no effect on the locking action of solids within the grooves, but can have a dramatic influence on the filling and packing unless a screw of appropriate design is used.

Experimental and Numerical Analysis of Thin-Wall Injection Molding with Micro-Features
Liyong Yu, Chee Guan Koh, Kurt W. Koelling, L. James Lee, Marc J. Madou, May 2001

Injection molding of thermoplastics with small feature size is needed in many medical and bio-chemical applications, i.e., bioMEMS. Three types of mold inserts, CNC machined steel mold, photoresist molds, and photolithography produced nickel molds are tested in high speed and high pressure (i.e., thin-wall) injection molding. The feature size covers a range of 5 micrometers to several hundred micrometers. Two optically clear thermoplatics (PMMA, PC) were processed under different molding conditions including mold temperature, injection speed, shot size, and holding pressure. The replication accuracy, molded-in stress, and mold wear were measured. Numerical simulation was carried out to calculate flow front profile and stress distribution. The simulation and experimental data were compared and the results can be used to design the process window for micro-injection molding.

Rheological Behavior of Thermotropic Liquid Crystalline Copolyester Vectra A950
Tianren Guo, Graham M. Harrison, Amod A. Ogale, May 2001

An investigation of the transient, steady and dynamic flow properties of the thermotropic liquid crystalline polymer Vectra A950 (Ticona) is presented. The steady viscosity curve shows the typical three-region flow curve of LCPs. In the transient shear experiments, the shear stress grows during the start-up of constant shear rate flow and goes through a maximum at approximately ?=2. Dynamic mechanical experiments show the existence of a linear viscoelastic region at small strains, and that the onset of nonlinearity varies with frequency. In the linear viscoelastic region, the storage and loss modulus, G'(?) and G(?) do not display the typical dependence on ?2 and ? respectively. The results obtained for a frequency sweep using constant strain and constant stress instruments are qualitatively different."







SPE-Inspiring Plastics Professionals

© 2024 SPE-Inspiring Plastics Professionals.
All rights reserved.

84 countries and 60k+ stakeholders strong, SPE unites plastics professionals worldwide – helping them succeed and strengthening their skills through networking, events, training, and knowledge sharing.

No matter where you work in the plastics industry value chain-whether you're a scientist, engineer, technical personnel or a senior executive-nor what your background is, education, gender, culture or age-we are here to serve you.

Our members needs are our passion. We work hard so that we can ensure that everyone has the tools necessary to meet her or his personal & professional goals.

Contact Us | Sitemap | Data Privacy & Terms of Use

Links

Locations

SPE US Office
83 Wooster Heights Road, Suite 125
Danbury, CT 06810
P +1 203.740.5400

SPE Australia/New Zealand
More Information

SPE Europe
Serskampsteenweg 135A
9230 Wetteren, Belgium
P +32 498 85 07 32

SPE India
More Information

SPE Middle East
More Information

3Dnatives Europe
157 Boulevard Macdonald
75017, Paris, France
More Information

Powered By SPE

SPE-Inspiring Plastics Professionals

SPE-Inspiring Plastics Professionals

SPE ImplementAM

SPE-Inspiring Plastics Professionals

SPE-Inspiring Plastics Professionals

SPE-Inspiring Plastics Professionals




spe2018logov4.png
  Welcome Page

How to reference articles from the SPE Library:

Any article that is cited in another manuscript or other work is required to use the correct reference style. Below is an example of the reference style for SPE articles:

Brown, H. L. and Jones, D. H. 2016, May.
"Insert title of paper here in quotes,"
ANTEC 2016 - Indianapolis, Indiana, USA May 23-25, 2016. [On-line].
Society of Plastics Engineers
Available: www.4spe.org.

Note: if there are more than three authors you may use the first author's name and et al. EG Brown, H. L. et al.

If you need help with citations, visit www.citationmachine.net